cavity wall

英 [ˌkævəti ˈwɔːl]

美 [ˌkævəti ˈwɔːl]

n.  (有保暖作用的)空心墙，夹壁墙

医学

牛津词典

noun

• （有保暖作用的）空心墙，夹壁墙
  a wall consisting of two walls with a space between them, designed to prevent heat from escaping
  1. cavity wall insulation
     空心墙隔热

柯林斯词典

• N-COUNT (隔音或防寒的)空心墙，夹层墙
  Acavity wallis a wall that consists of two separate walls with a space between them. Cavity walls help to keep out noise and cold.
  1. ...cavity wall insulation.
     空心墙隔音材料

英英释义

noun

• a wall formed of two thicknesses of masonry with a space between them

双语例句

• A ( test): after being eroded through acid, the cavity wall was spread with EM dental adhesive, then filled with silver amalgam.
  A组：经酸蚀后在洞壁周围涂以薄层EM粘结剂，吹匀随即以银汞合金充填。
• However, the construction of cavity wall masonry is not included in the current relevant standard, so research in this area are relatively small.
  但是，建设空斗墙砌体结构的相关标准却未被列入我国现行的规范中，因此对这方面的研究也相对较少。
• Discussion on the calculation formulas of injection mold cavity wall thickness
  注塑模型腔壁厚计算公式讨论
• Insulate your home. Cavity wall insulation can cut heat loss through the wall by up to 60 percent.
  房屋隔热可以利用空心墙来减少热能损耗，降幅高达60%。
• After entering the chamber, because of edge effects by the cavity wall, the flow rate of blank uneven, showing a distinct layered flow.
  在进入腔体以后，因边部受到腔体壁的影响，坯料的流动速率不均匀，可见明显的分层流动。
• Cavity wall masonry structure is a kind of special structure, because of its simple construction, low cost, so long in many of our relatively low level of economic development are widely used in many areas.
  空斗墙砌体结构作为一种比较特殊的结构形式，由于其施工简便、造价低廉，因而长久以来在我国许多经济发展水平相对较低的地区得到广泛的采用。
• This paper has a deep research on thermal resistance of cavity wall.
  对夹芯墙热工性能进行了深入研究。
• Research and finite element analysis on the steel frame structure with new infilling cavity wall
  新型砌体复合填充墙钢框架体系试验研究及有限元分析
• During the shore period of observation, carcinoma node, dimension of the cavity, thickness of the cavity wall and volume of liquid in the cavity have dynamic changes.
  囊腔内壁有附壁“结节影”（癌结），腔内有液体，在短期观察中“癌结”、“囊腔大小”、“囊壁的厚度”和“腔内液量”均有动态变化。
• Aiming at the injection mold structures of female mold on stationary mold, the force on the famale mold and male mold are analysed, and the cavity wall thickness are calculated.
  针对凹模安装在定模上、凸模安装在动模上的注塑模结构，对矩形型腔模具进行了受力分析和型腔壁厚计算。